Search results for: 'blocks'

Bolt - main bearing cap for cast iron blocks

Thrust bearings for C&G Block

Main bearing shell set 3 main bearings, MAE

Oil pipe; pump to block

Rear seal housing dry sump lip seal kit #

Crank block

Oil delivery pipe iron block wet sump

Top idle gear 2L 35T

Rear seal housing with flat and lip seal - aluminium block 75mm

Rear seal housing with groove and lip seal - aluminium block 75mm

Oil pick up pipe - big bore

Rear seal housing with flat and lip seal - iron block 75mm

Rear seal housing with groove and lip seal - iron block 75mm

Cylinder block - cross bolted 1.5ltr #

Gasket Between Oil Filter & Block

Front main bearing cap

Cylinder head to block ring dowel

Cylinder Block #

Crankshaft 80.00mm 3.150" stroke MAE Mains #

Stud - head to side of block 2.0L

Bush for distributor drive shaft

Oil gallery plug - front 7/8 UNF x 1/2 OAL

Timing cover

Cylinder block 3.8ltr #

Bush for distributor drive shaft

Distributor drive shaft

Silent block pivot support - front engine mount CASTING

Cylinder block #

O-Ring for plug cup

Cylinder block in alloy - wet sump #

Cylinder block in alloy - dry sump #

Cylinder head stud set W/A alloy block

Cylinder head stud set N/A alloy block

Cylinder block

Water pipe block to radiator

Gasket for exhaust manifold to block joint T46

Water plate for block

Water plate for side of block without outlet CASTING

Water plate for side of block with outlet. Water plate for side of block with outlet CASTING

Gasket inlet manifold to block T51

Gasket for exhaust manifold to block joint T51

Cylinder Block

2nd idle gear in block

Engine gasket set (Wide angle wet sump) no rear seal

Crankshaft steel billet 12 weight

Engine gasket set (dry sump)

Piston 87mm - wide angle 10:1 CR

HT lead separator & brackets

Engine gasket set 3.8(Wide angle) no rear seal

Braided cam oil feed pipe KIT - iron block

Cylinder head stud set - W/A head to iron block

Dry sump kit for aluminium block

Crankshaft - 8 weight small nose #

Dry sump kit

Gasket between oil filter & block

Cylinder liner

Braided cam oil feed pipe to main oil gallery

Oil connector block for dry sump

Jaguar LWE engine, wide angle head, carburettors, alloy block, dry sump

Jaguar LWE engine, wide angle head, carburettors, alloy block, wet sump

Jaguar LWE engine, wide angle head, carburettors, iron block, dry sump

Jaguar LWE engine, wide angle head, carburettors, iron block, wet sump

Oil gallery bung

Stud - head to side of block 2.5L

Main bearing cap front - big dowel

Main bearing cap front - small dowel

Distributor drive shaft

Front timing cover

Oil delivery pipe alloy block wet sump

Sump to block gasket pair

Stud 9mm dia block to crankcase

Cylinder Block with drain tubes and plug cups #

Water plate for block

Stud 9mm dia block to crankcase for 6mm compression plate

Nut 9x1 cylinder block mounting

Water rail on side of cylinder block CASTING

Oil distribution block CASTING

Cylinder block with plug cups fitted #

Cylinder Block fitted with spark plug cups

Cylinder block #

Water Pipe On Side Of Block

Flanged bearing housing fitted to block

Cylinder block 2.5ltr #

Cylinder Block 1.5 & 2ltr #

Cylinder liner 2.5ltr - unfinished top and bore

Cylinder liner 2ltr honed to 86.40mm

Cylinder liner 1.5ltr honed to 81.60mm

Top idle gear 2.5L 37T