Search results for: 'jaguar type engine'

Jaguar LWE engine, wide angle head, carburettors, iron block, dry sump

Jaguar LWE engine, wide angle head, carburettors, iron block, wet sump

Jaguar LWE engine, wide angle head, carburettors, alloy block, dry sump

Jaguar LWE engine, wide angle head, carburettors, alloy block, wet sump

Engine gasket set (dry sump)

Engine gasket set 3.4(Wide angle) no rear seal

Engine gasket set 3.8(Wide angle) no rear seal

Engine gasket set (Wide angle wet sump) no rear seal

Inlet Valve for 3.4L W/A Engine 2" Dia

Fully Synthetic Race Engine Oil 10w40 (5 Ltr)

Rubber type seal for rear of sump

Driven HR6 10W-40 Fully Synthetic Engine Oil. 0.946ml

Breather housing and pipe type B

Breather housing and pipe type A

Water pump - D-Type #

Wide angle D-Type cam cover kit

Narrow angle D-Type cam cover kit

Exhaust manifold PAIR - D Type

Exhaust manifold PAIR - C-Type

Wide angle E-Type cam cover kit screw cap

Wide angle E-Type cam cover kit Monza cap

Cylinder head - E-Type straight port #

Narrow angle E-Type cam cover kit screw cap

Narrow angle E-Type cam cover kit Monza cap

Distributor clamp -single bolt type

Cylinder head - E-Type straight port assembly #

Cylinder head wide angle D-Type 3.4ltr #

Cylinder head wide angle D-type 3.8ltr #

Inlet manifold (narrow angle D-Type 45DCO3)

Cylinder head wide angle D-Type assembly 3.8ltr

Cylinder head wide angle E-Type wet sump assembly #

Gasket - oil return pipe - wet sump

Rear seal housing dry sump lip seal kit #

Washer - Copper for inlet face core plugs

Core plug for head - inlet face

Exhaust downpipe pair

Inlet manifold gasket

Cylinder head blanking plate

Cylinder head breather plate

Airbox

Sump 3.8

Damper and pulley kit Single V A-series

Rear seal housing with flat and lip seal - aluminium block 75mm

Rear seal housing with groove and lip seal - aluminium block 75mm

Oil pick up pipe - big bore

Rear seal housing with flat and lip seal - iron block 75mm

Front oil pump assembly

Oil Pipe Flange Gasket For LWE Sump

Oil pump gear 30T 1.5" bore

Oil pump gear 30T 1.6875" bore

Inlet manifold 7deg 45DCO3 assembly

Inlet manifold 40DCO3 #

Spin on oil filter - dry sump.

Spin on oil filter / cannister

Camshaft 0.4375 lift (narrow angle)

Damper and pulley kit dry sump LWE

Crank bolt lock tab - fluid damper

Piston ring for Omega piston 88mm short & normal compression height

Cylinder head to block ring dowel

Key steel for crankshaft nose 3/16

Gasket cylinder head blanking plate.

Damper and pulley kit

Cylinder head gasket 84mm bore 0.040" MLS

Lock tab washer for crank nose bolt

Gasket - adaptor plate to inlet manifold

Cylinder head front cover gasket

Cam Cover Inlet Side With Breather Boss (lightweight)

Sump kit

Crankshaft 12 weight small nose #

Flange for water pump pulley

Cap for pressure relief valve

Distributor drive shaft

Water pump #

Adaptor, threaded for 2" Monza cap

Cometic 4.2 Head Gasket 0.043"

Crankshaft sprocket - large bore 1.687"

Cylinder block 3.8ltr #

Oil pump with doweled mounting holes

Screwed core plug - rear

LH Upper Chain Guide

Sump - aluminium

Gasket - sump bottom

Inlet manifold 0deg 45DCO3 #

Breather dry sump

Cylinder block in alloy - wet sump #

Cylinder block in alloy - dry sump #

Oil filter adaptor

Water pump pulley

Water pump - LWE #

Inlet manifold 7deg 45DCOE #

Inlet manifold 7deg 45DCO3 #

Inlet manifold 0deg 48DCOE #

Inlet manifold 0deg 45DCOE #

Cylinder head stud set W/A alloy block

Cylinder head stud set N/A alloy block

Oil return pipe for side exit oil filter

Damper and pulley kit wet sump LWE

Crankshaft steel billet 12 weight

Flywheel 104T 9 1/2 " single plate clutch

Inlet manifold adaptor plate 1 3/4 dia