Search results for: '1 5 plate'

Inlet manifold adaptor plate 1 3/4 dia

Water plate for block

Square bronze plate on rear of cambox

Manifold plate with O-rings

Carburettor plate in aluminium 45mm DCOE

Dynamo end plate for rev counter take off

Top cover plate for sump on rear CASTING

Keep plate for cam gear

Flywheel 104T 9 1/2 " single plate clutch

Keep plate for idle gear in head

1959 MGA TWIN CAM ROADSTER

Water plate - copper

Clutch plate 1 1/8'' 10 Spline

Clutch Plate 1 1/8'' 10 Spline (center plate)

Water plate - no outlet CASTING

Water plate with outlet CASTING

Stud 5/16" UNC - UNF x 1.5"

Round cover plate on front of head front cover

Stud 5/16" UNC - UNF x 1.75"

Stud 5/16" UNC - UNF x 1.25"

Stud 5/16" UNC - UNF x 1.375"

Stud 5/16" UNC - UNF x 1.125"

Clutch plate cerametallic 9 1/2" dia 1 1/8" 10 spline

Clutch 7 1/4 triple plate with 1 1/8" 10 spline clutch plates

Blanking plate for cylinder head

Bell housing cover plate CASTING

Engine backplate

Choke blanking plate CASTING

Gasket - adaptor plate to inlet manifold

Backplate FPF - ZF -18 degrees with seal housing and bolt

Cover plate

Backplate (FPF - 18 Queerbox) assembly with seal housing

Exhaust Manifold Plate

Limited Slip Differential plate type in steel 3.14 - 3.77 std 27mm offset 40/65 ramps 120Nm

Brake backplate CASTING

Inlet manifold carburettor plate 50DCO3

Stud 9mm dia block to crankcase for 6mm compression plate

Camshaft damper interior plate

Tacho drive take off plate

Engine backplate FPF - Ersa mk1

Chassis plate

Backplate plate FPF - HD5

Stud 3/8'' UNC - UNF x 1.5''

Pad retainer plate

Pad retainer plate

Pad retainer plate

Steel plate for 1st gear

Backplate assembly

Adaptor plate - aluminium C5S

Breather blanking plate

Backplate FW - MGA

Clutch Plate 1'' 10 Spline

Cover plate for sump

Inlet manifold carburettor plate 45DCO3

Inlet manifold carburettor plate 45DCOE

Plate; retainer shaft

Inlet manifold plate 2.5ltr

Rear brake backplate for 270mm drums

Cam Gear Keep Plate

Wheel stud 2.5" long 3 7/16" overall

Wheel stud 2.25" long 3 3/16" overall

Engine backplate - aluminium for lip seal

Gearbox assembly Cooper T51 4 speed Mk2

Plate differential

Backplate assembly FW - MGA

Cover plate for sump CASTING

Rear brake backplate for 270mm drums CASTING

Plate for locking spigot bearing

Cover plate gasket

Engine backplate - FW to MG Midget gearbox

Supercharger end plate front or rear CASTING

Ram pipe retaining plate

Compression plate 6mm

Dry clutch pack - ceramic plates

Oil drain plate CASTING

Limited slip differential multi plate

Gasket cylinder head blanking plate.

Stud - head to side of block 2.5L

Cover plate for selector shafts (lip seal)

Chassis plate - Paxalin

End plate for supercharger

Chassis plate - aluminium

Locking plate layshaft & reverse shaft

Cover plate for selector shafts with lip seal kit

Cover plate for selector rods

Windage Plate / Sump Baffle

Clutch plate organic 9 1/2" dia 1 1/8" 10 Spline

Clutch plate outer for starter

Clutch plate inner for starter

Differential - plate type

Output shaft & flange housing Cobra assembly with spacer plate. Bolt length 1.625"

Choke blanking cover

End plate for supercharger CASTING

Chassis plate - Lotus Cars Tottenham Lane

Chassis plate - Lotus Components Cheshunt

Engine side plate CASTING

Exhaust manifold plate for oval port

Blanking plate for cam cover breather hole

Inlet manifold plate (small high port)

Support plate for leather coupling